Pelco DVR DX3016-060 Manuel d'utilisateur Page 81
- Page / 85
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
80 Pelco Manual C681M-D (2/02)
Description of problem Please consult the following
The unit will not turn on.
Power is on, but the unit will not
operate.
Images are not appearing on the
monitor.
The quality of the monitor picture is poor.
The unit will not start recording.
The unit will not stop recording.
The unit will not perform Repeat
Recording.
The unit will not perform Timer
Recording.
The unit will not perform Alarm
Recording.
The unit will not perform playback.
The copying device/archive device does
not respond.
Power is on, but I cannot get past the
“SETTING UP ...” display.
The unit will not backup all of the data
on the hard disk.
Is the power cord properly plugged in?
Is the LOCK indicator light on?
Is the TIMER REC indicator light on?
Is the LOCK indicator light on?
Is the POWER button blinking? (The unit cannot be operated when the POWER button is blinking and it’s
the same when the other buttons and indicators are blinking.)
It is possible that the safety features are in operation.
Restart the unit by pressing the RESET button located at the back of the unit using a ballpoint pen or similar
object.
Is the REMOTE communication indicator light on (DX3016 models only)? Press the REMOTE communica-
tion button to turn off the light.
Are the monitor and camera(s) connected correctly?
Is the unit receiving an input signal from the selected camera?
Check this by setting the unit to SPLIT 9.
Is the connecting cord connected correctly?
Is the camera’s focus adjusted correctly?
Is there any recording space left on the disk?
The unit begins recording only after the specified recording time. Was the unit stopped during the specified
recording time?
Is the PRE ALARM REC indicator light on?
Is the LOCK indicator light on?
Is the unit running in Timer Recording mode? If so, cancel the Timer Recording and press the TIMER REC
button once again.
Is the unit running in Repeat Recording mode?
Are the date and current time set accurately?
Are the Recording Start-/End-times and the recording interval set correctly?
If the recording interval has been set correctly, then has the recording medium been placed in the unit?
Has the recording medium’s write-protect been removed?
Is the HDD Repeat Recording setting set on REC•STANDBY?
Is the unit in stand-by mode?
Are the peripheral switches, etc., connected correctly?
Is the LOCK indicator light on?
Has the image data been erased?
Has the playback device been selected correctly?
Is the PRE ALARM REC indicator light on?
Has the recording medium been inserted correctly into the unit?
Is the unit currently in the middle of loading the recording medium?
Has the playback device been selected correctly?
Has the peripheral recording device been selected correctly?
Is the peripheral recording device’s SCSI ID number set correctly?
Is the SCSI terminator switch off?
Inspect the recording medium.
Check the amount of available recording space.
INSTALLATION
RECORDING
PERIPHERAL RECORDING
DEVICE
PLAYBACK
TROUBLESHOOTING
If problems with the unit persist even after you’ve followed the suggestions below, please disconnect the power cord and contact
Pelco’s Technical Support Group at 800-289-9100.
- DX3000 Series 2
- Digital Recorder 2
- Installation/ 2
- Operation Manual 2
- C681M-D (2/02) 2
- CONTENTS 3
- Pelco Manual C681M-D (2/02) 3 4
- LIST OF ILLUSTRATIONS 5
- Pelco Manual C681M-D (2/02) 5 6
- OVERVIEW 7
- FRONT PANEL CONTROLS 8
- Setting) menu 9
- Pelco Manual C681M-D (2/02) 9 10
- REAR PANEL CONNECTORS 11
- Warnings 12
- INSTALLATION 13
- POWER ON/POWER OFF/ 14
- ALARM IN/REC/CLOCK ADJ 14
- Input terminal 14
- • Input Circuit 14
- Second Unit 15
- First Unit 15
- Te rminator 16
- Programming 17
- Adding a Hard Drive(s) 17
- REMOVING A HARD DRIVE(S) 18
- BOOT-UP DELAY 18
- PROGRAMMING 19
- MAIN MENU 20
- SUB MENU (1) 20
- SUB MENU (2) 20
- SUB MENU (3) 20
- SUB MEN U ( 1 ) SUB MENU (2) 21
- (NOT USED) 22
- IMAGE QUALITY 23
- MAXIMUM RECORDING FIELDS 23
- DEFINE GROUP SETTING 24
- ALARM RECORDING DURATION 25
- RECORD ALARM 25
- PRE-ALARM RECORDING 26
- Motion Detection 27
- OVERWRITE 28
- AUDIO RECORDING 29
- AUTO EJECT 29
- CALL OUT 31
- CAPACITY REMAINING 31
- DATA CLEAR (ERASE) SELECTION 32
- This menu item 33
- HARD DISK DRIVE (HDD) FULL 34
- IM-CHECK MODE 35
- INITIALIZE MENUS 36
- MODE OUT 36
- Detection During a Timer 37
- Recording 37
- MULTIPLEXER DISPLAY 39
- Nine-Camera (Split 9) Setting 39
- Four-Camera (Split 4) Setting 40
- Operation 43
- ALARM DISPLAY 44
- Power Failure 45
- Recording Time 46
- Define Group 47
- RS-232C COMMUNICATION 48
- SAVING MENU SETTINGS 49
- SAVING MENU DATA 49
- RESTORING MENU DATA 49
- TIME AND DATE DISPLAY 50
- DISPLAY MODE 50
- CHARACTER SIZE 51
- CLOCK LOCATION 52
- TIME AND DATE SETTING 52
- TIMER RECORDING 53
- Select Re 54
- 14:00 15:00 16:00 17:00 55
- Timer Recording 56
- DX3009 Recording Time Tables 57
- DX3016 Recording Time Tables 57
- OPERATION 58
- ZOOM BUTTONS 60
- REMOTE VIEWING 60
- RECORDING 60
- BASIC RECORDING 60
- Playback 61
- PAUSE PLAYBACK 63
- REVERSE PLAYBACK 63
- ADJUSTING PLAYBACK SPEED 63
- Regular Playback Mode 63
- Time and Date Display 64
- Index Search 65
- Skip Search 66
- Alarm List Search 67
- Jump to Starting Point 67
- Auto Eject 69
- 30F 15F 7.5F 5F 70
- Using the COPY Button 71
- Backing up Data 71
- INFORMATION 72
- ELAPSED TIME DISPLAY 72
- POWER FAILURE LIST 72
- DX3009 RECORDING TIME TABLES 74
- STANDARD 75
- SUPERIOR 75
- SUPERIOR 77
- STANDARD 77
- WARNINGS 80
- TROUBLESHOOTING 81
- SPECIFICATIONS 83
- REGULATORY NOTICES 85
Produits connexes et manuels pour Enregistreurs vidéo numériques (DVR) Pelco DVR DX3016-060
(78 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.200 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels