Pelco C1306M-B Manuel d'utilisateur

ExSite™ EHXM SeriesExplosionproofFixed SystemINSTALLATIONC1306M-B (10/06)

10 C1306M-B (10/06)Table B. D Protocol Receiver Address (Continued)ADDRESSSWITCH SETTINGSW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8143 ON ON ON O

C1306M-B (10/06) 11ADDRESSSWITCH SETTINGSW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-8239 ONONONONOFFONONON240 OFF OFF OFF OFF ON ON ON ON241 ON OFF

12 C1306M-B (10/06)Install the Camera ModuleTo install the camera module, do the following:1. Refer to Figure 4. Loosen the set screw at the back of t

C1306M-B (10/06) 133. Slide the camera module into the camera enclosure. Refer to Figure 6 to position the camera module properly in the camera enclos

14 C1306M-B (10/06)4. Models with a wiper: Refer to Figure 8 and do the following to install the arm of the wiper:a. Place the supplied green bushing

C1306M-B (10/06) 15Install the Enclosure and Set Pan Position1. Check for proper seating of the power module seal. Make sure the seal is fully seated

16 C1306M-B (10/06)Set the Tilt Angle of the Camera Module1. Place a 41 mm open end or crescent wrench on the tilt locking nut and a 21 mm open end wr

C1306M-B (10/06) 17Install the Sun Shroud1. Place the supplied nylon washers on the 6-32 Phillips pan head screws. Refer to Figure 12.2. Align the mou

18 C1306M-B (10/06)MaintenanceCAMERA MODULE REPLACEMENTTo replace the camera module, do the following:1. Remove the back cap of the camera enclosure.

C1306M-B (10/06) 193. Models with a wiper: Remove the wiper arm and the green bushing from the unit (refer to Figure 14). 4. Slide the camera module o

2 C1306M-B (10/06)ContentsList of Illustrations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

20 C1306M-B (10/06)6. Models with a wiper: Refer to Figure 14 and do the following to reinstall the arm of the wiper:a. Reinstall the green bushing on

C1306M-B (10/06) 21SpecificationsELECTRICALInput Voltage 24 VAC or 100-240 VACInput Voltage Range ±10%Power Consumption Maximum 60 W (120 VA) per sy

22 C1306M-B (10/06)*Manual control of camera setup functions can be done with CM6700, CM6800, CM8500, CM9500, CM9740, CM9760, CM9770, CM9780, KBD200

The materials used in the manufacture of this document and its components are compliant to the requirements of Directive 2002/95/EC.This equipment con

Worldwide Headquarters3500 Pelco WayClovis, California 93612 USAUSA & CanadaTel: 800/289-9100Fax: 800/289-9150InternationalTel: 1-559/292-1981Fax:

C1306M-B (10/06) 3Important Safety Instructions1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5

4 C1306M-B (10/06)Getting StartedThank you for purchasing Pelco’s ExSite™ EHXM Series explosionproof system. This manual includes instructions for ins

C1306M-B (10/06) 5Install the Power ModuleAttach the power module to the mounting surface. Use only installation methods and materials capable of supp

6 C1306M-B (10/06)CONNECT WIRINGRefer to the following information to connect the wires and cables as required.NOTES: • Relay 3 is allocated specific

C1306M-B (10/06) 7DIP SWITCH SETTINGSConfigure the receiver address, termination, and baud setting for the system. The DIP switches to configure these

8 C1306M-B (10/06)ADDRESSSWITCH SETTINGSW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-81 OFF OFF OFF OFF OFF OFF OFF OFF2 ON OFF OFF OFF OFF OFF OFF OF

C1306M-B (10/06) 9ADDRESSSWITCH SETTINGSW1-1 SW1-2 SW1-3 SW1-4 SW1-5 SW1-6 SW1-7 SW1-849 ON OFF OFF OFF ON ON OFF OFF50 OFF ON OFF OFF ON ON OFF OFF51