Pelco ESPRIT ES30C Manuel d'utilisateur

ES30C/ES31C SeriesEsprit® with IOPC309M-J (9/04)®OPERATION/PROGRAMMING

10 C309M-J (9/04)PROGRAMMING - ES30C22/ES31C22Backlight comp OffZoom limit x- -Reset camera<Gain/AGC><Auto iris>NextExitCamera MenuLine

C309M-J (9/04) 11PROGRAMMING - ES30CBW18/ES31CBW18Backlight comp OffZoom limit x72Reset camera<Gain/AGC><Auto iris>NextExitCamera MenuLi

12 C309M-J (9/04)PROGRAMMINGACCESSING MAIN MENU (PRESET 95)You can call up the main menu on your monitor by programming (setting or creating) preset 9

C309M-J (9/04) 13AUTO FOCUS MODEThere are two auto focus modes:Auto – If auto focus is in the auto mode, pressing the Focus Far or Focus Near button w

14 C309M-J (9/04)AUTO IRISThe following are the settings for auto iris:ModeLevelPeakTo change the settings for auto iris:1. Program preset 95 (28). Th

C309M-J (9/04) 15AUTO IR LEVEL (MODELS ES30CBW18/ES31CBW18 ONLY)The auto IR level is the light level at which the infrared filter switches IN or OUT.

16 C309M-J (9/04)AUTO SHARPNESS The following settings are available for auto sharpness:On – Automatically sets the sharpness of the camera.Off – The

C309M-J (9/04) 17AZ/ELAz/El programs the horizontal display position of the Azimuth1/Elevation2 label.NOTE: Az/El display is not available while you

18 C309M-J (9/04)AZ/EL LINEAz/El Line controls the vertical display position of the Azimuth/Elevation label. The label may be displayed on lines 3 thr

C309M-J (9/04) 19AZIMUTH ZEROAzimuth is the pan angle from 0° to 359°. Azimuth zero is the programmed 0° point that is normally set to magnetic north.

2 C309M-J (9/04)

20 C309M-J (9/04)BACKLIGHT COMPENSATIONThere are two backlight compensation modes:On – The system uses the center 10 percent of the picture to adjust

C309M-J (9/04) 21DIRECTIONDirection programs the horizontal display position of the Direction label (N, NW, NE, …).NOTE: For direction to be accurate

22 C309M-J (9/04)DIRECTION LINEDirection Line controls the vertical display position of the Direction label. The label may be displayed on lines 3 thr

C309M-J (9/04) 23DISPLAY DURATIONDisplay Duration programs the duration the Az/El, Direction, and Zoom labels are displayed on the monitor. The availa

24 C309M-J (9/04)GAIN LIMITThe gain limit sets the maximum level for the automatic gain control. Increasing the level will increase the signal level a

C309M-J (9/04) 25IR FILTER MODE (MODELS ES30CBW18/ES31CBW18 ONLY)There are two settings for the IR filter mode:Auto – IR filter switches in and out au

26 C309M-J (9/04)LIMIT STOPSNOTE: Limit stops are inactive while setting items in the program menu (e.g. azimuth zero, scan limits, manual pan limits

C309M-J (9/04) 27LIMIT STOPS MENUThe manual pan limit stops can be set at the controller using the Limit Stops menu:1. Program preset 95 (28). The mai

28 C309M-J (9/04)Scan Limit StopsWhen scan limit stops are set, the pan and tilt reverses direction during random, frame, or auto scanning when a limi

C309M-J (9/04) 29LINE SYNCHRONIZATIONIf cameras are out of phase with each other, they may produce what appears to be vertical roll when switching bet

C309M-J (9/04) 3CONTENTSSection PageIMPORTANT SAFETY INSTRUCTIONS ...

30 C309M-J (9/04)LOWLIGHT LIMIT (MODELS ES30C22/ES31C22 AND ES30CBW18/ES31CBW18 ONLY)This setting determines the maximum length of time the shutter wi

C309M-J (9/04) 31PARK TIME MINUTESThis feature causes the system to park at preset 1 after a programmed number of minutes of control inactivity. The t

32 C309M-J (9/04)PATTERN LENGTHThe Esprit can do the following:One full pattern - 1.5, 3, or 6 minutes longorTwo half patterns - .75, 1.5, or 3 minute

C309M-J (9/04) 33POWER-UP MODEThis feature lets the dome resume a desired condition following power-up. The menu includes the following choices.• Defa

34 C309M-J (9/04)PROPORTIONAL PANThere are two proportional pan modes:On – Enables the proportional pan mode. The amount of zoom controls the pan and

C309M-J (9/04) 35RESET CAMERADefault Setting<Camera><Line Sync><Power Up><Wiper><Limit Stop><Other>ExitMAIN MENUBa

36 C309M-J (9/04)SCAN SPEEDThe scan speed is adjustable from 1-40 degrees per second. This occurs in three scan modes: auto, random, and frame scan.To

C309M-J (9/04) 37SHARPNESSUse the Sharpness setting to manually set the sharpness of the camera.To manually set the sharpness of the camera:1. Program

38 C309M-J (9/04)SHUTTER SPEEDThere are several electronic shutter speed settings:Auto1/21/41/81/151/301/601/1201/1801/2501/5001/10001/20001/40001/10,

C309M-J (9/04) 39SPEED PROFILEThis feature allows the operator to set the wind speed conditions for the location of the Esprit system. You can set two

4 C309M-J (9/04)WHITE BALANCE ...

40 C309M-J (9/04)WHITE BALANCEThe settings for white balance are as follows:Auto white balR GainB GainTo change the white balance settings:1. Program

C309M-J (9/04) 41WIPER MODEThere are three wiper settings:Wiper ModeWiper DwellWiper TimeTo change the wiper settings:1. Program preset 95 (28). The m

42 C309M-J (9/04)The Esprit system features onscreen programmable zone blanking. This feature lets you define any zone as blanked for video (viewing/r

C309M-J (9/04) 43ZOOMZoom programs the horizontal display position of the Zoom label. The following settings are available for the Zoom label:Off – La

44 C309M-J (9/04)ZOOM LIMITES30C16/ES31C16 - 16X optical zoom and 10X electronic zoom, can be set for 16X, 32X, 64X, 128X, or 160X.ES30C22/ES31C22 - 2

C309M-J (9/04) 45ZOOM LINEZoom Line controls the vertical display position of the Zoom label. The label may be displayed on lines 3 through 10. Line 3

46 C309M-J (9/04)SPECIFICATIONSELECTRICALInput Voltage: 24, 120, or 230 VAC, 50/60 Hz; switch selectable for 120/230 VAC inputs. Reset feature enabled

C309M-J (9/04) 47SensitivityES30C16/ES31C16: 0.05 lux at 1/2-second shutter speed (NTSC)0.05 lux at 1/1.5-second shutter speed (PAL)ES30C22/ES31C22: 0

REVISION HISTORYManual # Date CommentsC309M 9/00 Original version.C309M-A 12/00 Added information on “Pan Limit” message per ECO #00-6635.C309M-B 6/01

C309M-J (9/04) 5IMPORTANT SAFETY INSTRUCTIONS1. Read these instructions.2. Keep these instructions.3. Heed all warnings.4. Follow all instructions.5.

Worldwide Headquarters3500 Pelco WayClovis, California 93612 USAUSA & CanadaTel: 800/289-9100Fax: 800/289-9150InternationalTel: 1-559/292-1981Fax:

6 C309M-J (9/04)OPERATIONPOWER-UP DISPLAYWhen the system is powered up, the selected protocol, revision number, and other information is displayed on

C309M-J (9/04) 7OPERATING NOTESENVIRONMENTAL RANGEThe operating temperature ranges from a minimum of -50°F (-45°C) to a maximum of 122°F (50°C) for su

8 C309M-J (9/04)PATTERNSThe Esprit system can do either one full pattern (1.5, 3, or 6 minutes long) or two half patterns (.75, 1.5, or 3 minutes long

C309M-J (9/04) 9PROGRAMMING - ES30C16/ES31C16Backlight comp OffZoom limit x- -Reset camera<Gain/AGC><Auto iris>NextExitCamera MenuLine S